Ghost Controls Access Control Installation Nationwide

Ghost Controls Access Control Installation: The Fort Worth Owner’s Guide

We install Ghost Controls-compatible access control systems throughout Fort Worth, and most homeowners pay between $325 and $780 installed, depending on the keypad, receiver, or board your setup needs. We keep the most common Ghost Controls access control parts on the truck, so a single visit usually gets your gate working again. If your keypad stopped responding, your remote lost range, or the gate no longer recognizes your entry code, you’re likely dealing with a failed access control component, not a bad motor.

Call (817) 840-7067

Which Ghost Controls Models This Applies To

Ghost Controls builds access control into two main product lines: the original gate opener series (AXDP, AXDP2, and the newer HDP series) and the vehicle detection add-ons like the VDP photocell and the AXZD magnetic lock. The access control side of things covers the wireless keypad (AXWK), the vehicle sensor, the exit wand, and the receiver board that talks to your remotes. Here’s the compatibility gotcha most Fort Worth owners run into: Ghost Controls changed their receiver frequency on the HDP series, so a keypad or remote bought for an old AXDP opener won’t pair with a new HDP board. You have to match the frequency printed on the receiver label. If the label is faded or missing, we can identify the board version by the connector layout and the FCC sticker inside the housing. We carry OEM Ghost Controls parts and quality aftermarket equivalents. For the access control pieces specifically, we recommend OEM. The aftermarket keypads work, but the weather-seal on the OEM pad holds up far better through three or four Texas summers, and that failing seal is the number one reason keypads short out in this market.

Signs Your Ghost Controls Access Control Installation Is Failing

• Keypad lights up but the gate won’t move. This usually means the keypad is sending a signal but the receiver board on the opener isn’t decoding it. The keypad itself may be fine. We test the board before replacing anything, because a $40 keypad swap won’t fix a $160 receiver problem, and we don’t bill for parts that weren’t the issue.
• Remote range drops from 80 feet to 20 feet, or only works at the gate. That’s a classic receiver board degradation pattern. In Fort Worth’s summer heat, the solder joints on the older AXDP receiver boards develop hairline cracks that expand and contract with temperature. When the board cools at night, the gate works; at 3 p.m. in August, it acts dead.
• Gate opens randomly without anyone pressing anything. Usually a failing exit wand or a vehicle sensor picking up interference from a nearby radio tower or power line. We’ve tracked down phantom openings in the Ridglea Hills area to a faulty sensor wire that was acting like an antenna.
• Keypad beeps but doesn’t accept your code. The rubber buttons wear through over time, especially if the keypad faces direct west sun. Once the membrane tears, moisture gets under the keypad face and corrodes the contact points. Your code is still stored; the pad just can’t register the button press.
• Vehicle sensor won’t trigger the gate for a motorcycle or a lower-slung car. Ghost Controls vehicle sensors are tuned for a metal mass threshold, and smaller vehicles sometimes fall below it. This isn’t always a failed part. Sometimes it’s a height adjustment or a sensor placement issue, which costs less to fix than replacing the sensor.

Replacement Cost & What’s Included

In Fort Worth, expect to pay $325 to $480 for a keypad replacement (part and labor), $380 to $620 for a receiver board replacement, and $450 to $780 for a full access control setup that includes a new keypad, receiver, and programming. The range comes down to which Ghost Controls series you have: AXDP parts are less expensive than HDP parts, and if your system is old enough that we need to run new low-voltage wire from the keypad to the board, that adds labor. Every quote is written before work starts, so the number you approve is the number you pay. The work carries our written one-year guarantee. The Garrison Standard applies across the board: background-checked technicians, uniformed crew, and a cleanup before we leave. If anything fails inside that year, we come back and make it right at no charge.

DIY or Call Us?

There are a couple of safe checks you can do yourself. Confirm the keypad has fresh batteries, and verify the opener itself is getting power from its outlet or breaker. Beyond that, access control work gets into low-voltage wiring on a motor system that’s connected to house power. If you mis-wire a keypad into the board, you can short the main control board, and then a $325 keypad job becomes a $620 board job. Lonnie Burke puts it this way: “Tell me what it’s doing wrong, and I’ll tell you exactly what it needs.” We’d rather talk you through a two-minute phone diagnosis than have you spend a Saturday afternoon chasing a wiring gremlin. Call (817) 840-7067 and describe the symptom. If it’s something simple, we’ll tell you over the phone. If it needs a tech, we’ll give you a written price before anyone turns a screw.

FAQs

Call Carver Gate Repair Fort Worth

If your Ghost Controls keypad, receiver, or sensor is failing, call (817) 840-7067. You’ll get a live person, a straight answer, and a written price before any work starts. We work on Ghost Controls equipment as an independent service provider, not a Ghost Controls dealer, which means our only loyalty is to getting your gate working right for the price we quoted. Lonnie Burke and the crew serve Fort Worth and the surrounding areas with background-checked technicians, upfront pricing, and a one-year written guarantee on every repair.

Written by Lonnie Burke, Owner, Carver Gate Repair Fort Worth at Carver Gate Repair Fort Worth, serving Fort Worth and nearby areas.