FAAC Gate Repair Nationwide

FAAC Gate Repair in Fort Worth: What to Know First

We repair FAAC gate operators and gate hardware across Fort Worth, typically completing a service call within one to three business days depending on the part needed. Most FAAC repairs run between $185 and $640, and you’ll get a written price before any work starts so the number never moves on you. If you’ve got a FAAC swing gate that’s grinding, beeping without moving, or refusing to close, call (817) 840-7067 and we’ll schedule a tech to come out and diagnose it properly.

Call (817) 840-7067

This page is for homeowners and property managers in Fort Worth who own a FAAC gate system and want straight answers on what it costs to fix, how the failure actually works, and whether the operator is worth saving. We’re an independent FAAC service provider, not a manufacturer-authorized shop, which means we fix what’s broken rather than steering you into a replacement because it’s easier for us.

Key Takeaways:

• FAAC repair in Fort Worth typically costs $185 to $640, with a written quote before work begins
• Most FAAC failures trace to limit switches, capacitors, or hydraulic fluid issues, not the motor itself
• Every repair carries a written one-year guarantee through our 365-Day Done Right Promise
• We service all major FAAC lines including 400, 750, 770, E024U, and S800H series

How FAAC Products Fail – and How We Fix Them

FAAC builds solid operators, but every model line has its patterns. Here’s what we actually see on FAAC gates in Fort Worth:

• Hydraulic fluid loss on C720 and C721 series operators. These older hydraulic swing gate units push a lot of cycles, and over time the shaft seals dry out and weep fluid. The gate starts sluggish in cool weather, then becomes erratic in the Texas summer heat. We rebuild the piston seals and refill with the correct FAAC hydraulic fluid rather than masking it with a generic top-off that’ll leak out again in a month.
• Limit switch drift on 400 and 402 swing operators. The mechanical limit cams inside these units wear down, so the gate overshoots its open position and grinds against the stop. Technicians who don’t know FAAC gear will chase the problem with control board adjustments that never hold. The fix is replacing the cam assembly and re-setting the open and close stops, which we do on the bench before reinstalling the cover.
• Capacitor failure on 750 and 770 sliding gate operators. These are the workhorses of Fort Worth commercial and larger residential properties. The start capacitor goes bad and the motor just hums, clicks, or trips the board fault. A $35-to-$55 capacitor is often the whole repair, but plenty of homeowners get quoted a full operator replacement. We test the capacitor under load before condemning the board or motor, so you pay for what’s actually failed.
• Control board damage from lightning and power surges on E024U and S800H series. North Texas storms are hard on gate electronics. FAAC boards are well-built but they don’t enjoy the surge a nearby strike pushes through the low-voltage wiring. We hard-wire a surge arrestor at the control panel and recommend the same on the power supply, which prevents the same board from getting knocked out again next storm season.
• Gate sag from settling posts on FAAC swing installations. The operator didn’t fail – the hinge post shifted in the North Texas clay, which put the gate leaf out of square and forced the operator to work twice as hard. We’ll reweld or shim the hinge, re-square the leaf, and reset the operator limits so the FAAC unit isn’t pushing against its own geometry. This is a Fort Worth climate reality we handle constantly in older neighborhoods like Crestline and Park Hill.

Our FAAC Gate Repair Process

Every FAAC job follows the same sequence, and it’s designed so you know exactly what’s wrong before you spend a dollar on parts:

1. 1
   Call and describe the symptom. We ask you what the gate’s doing, not just “it’s broken.” A hum versus a click versus a half-open stall points to different failures. As Lonnie puts it, “Tell me what it’s doing wrong, and I’ll tell you exactly what it needs.”
2. 2
   On-site diagnosis. The technician tests voltage, checks limit switch continuity, inspects hydraulic level and seal condition, and watches the gate run a full open-close cycle. We find the actual root cause, not a symptom site.
3. 3
   Written price before work starts. You get a typed or legibly written quote with the part number, labor, and total. You approve it, or you don’t – the price never changes on the door.
4. 4
   The repair itself. We use OEM FAAC parts when the repair is under manufacturer warranty or when aftermarket parts don’t hold tolerances. For older out-of-warranty units, we’ll use quality aftermarket components that we’ve tested for load rating and fit, always telling you which we’re putting in and why.
5. 5
   Full cycle test and safety check. The gate runs a minimum of five full open-close cycles. We check the entrapment protection, the photo sensors, and the force setting so the gate reverses properly if something’s in its path.
6. 6
   Cleanup and the written guarantee. The work area’s swept, old parts are hauled off, and you get the repair summary and guarantee paperwork before we leave. The guarantee runs a full year from the service date.

What FAAC Gate Repair Costs in Fort Worth

Here’s what we charge for the most common FAAC repairs in the Fort Worth area, including parts and labor:

• Start capacitor replacement on 750/770 series: $185-$260
• Limit switch or cam replacement on 400/402 series: $240-$380
• Hydraulic seal rebuild on C720/C721 series: $320-$540
• Control board replacement on E024U/S800H series (with surge protection added): $480-$640
• Full swing gate realignment with hinge and post repair: $410-$780

What moves the price is the part, not our labor rate, which is fixed. A proprietary FAAC board costs what it costs. A failing hinge post that needs fresh concrete takes longer than swapping a capacitor. You’ll always see the price in writing before we turn a single tool. Call (817) 840-7067 and we’ll give you a free estimate over the phone or after the on-site diagnosis, whichever gives you the clearer answer.

Why Fort Worth Homeowners Call Carver Gate Repair Fort Worth for FAAC Work

Lonnie Burke and the crew have been working on FAAC equipment in Fort Worth long enough to know the difference between a 402 and a 402A without pulling the cover, and that kind of familiarity means faster diagnosis and fewer wrong parts. We’re part of the Garrison Partners family and operate under The Garrison Standard – written prices, background-checked uniformed technicians, and a 365-Day Done Right Promise that’s spelled out on the guarantee sheet, not assumed. If we touch a FAAC operator and it fails inside a year for the same issue, we come back and make it right at no charge. No argument, no re-invoice.

We also service the other operators Fort Worth homes carry alongside FAAC units – LiftMaster, Mighty Mule, Ghost Controls, DoorKing – so when your property has two different gate systems or a mixed setup, one call handles it. Phones are answered by a live person at (817) 840-7067, every day, including weekends and holidays.

FAQs