Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Motor Repair in Fort Worth: What to Know First
Ghost Controls gate motor repair in Fort Worth typically runs $185 to $420 for most board, limit switch, and arm repairs, with full motor replacement on swing gates landing between $650 and $1,150 depending on the model and whether we’re replacing the arm assembly or just the internals. We’re an independent Ghost Controls service provider, not a factory shop, and most repairs are completed in one visit. You get a written price before any work begins, and every repair carries our full-year guarantee.
This page is for Fort Worth homeowners whose Ghost Controls opener has stopped responding, started beeping, or begun opening halfway and reversing. We work on the entire residential Ghost Controls line, from the original AXDP and TSS1 swing arms to the current R series and the VS series intended for heavier gates. Call (817) 840-7067 and you’ll reach a live person who can schedule a technician, not an answering service.
How Ghost Controls Products Fail – and How We Fix Them
Ghost Controls builds a solid residential opener, but every brand has its patterns. After years of working on these units across Fort Worth, we know what fails, why, and whether the right move is a repair or a full motor replacement.
- AXDP swing arm: stripped internal gear after a wind slam. The original AXDP arm uses a plastic internal gear that strips when a gust catches the gate and slams it against the stop. The symptom is a motor that runs but the gate doesn’t move, or it moves a few inches and grinds. We open the arm, confirm the gear is the culprit, and replace it with the factory gear set. If the gate has slammed more than once, we’ll also check the close limit and add a mechanical stop if the original is worn.
- TSS1 and R series: limit switch drift causing the gate to stop short or over-travel. These models use magnetic limit switches on the arm, and they’re picky about alignment. When the gate starts stopping six inches from closed or smacking the open stop, the limit has drifted. We realign the limit assembly and re-learn the travel on the board. This is a same-day repair in most cases.
- VS series on heavier gates: capacitor failure in the control board. The VS series runs bigger gates, and Fort Worth summer heat is hard on the board’s start capacitors. A gate that hums but won’t move, or trips the breaker repeatedly, often points to a cooked capacitor. If the board shows no other damage, we replace the capacitor rather than the whole board. If the capacitor has already been replaced once and failed again, we discuss a board swap and check the motor’s amp draw.
- All Ghost Controls models: receiver range loss after a transformer overheats. When the remote only works from ten feet away, the problem usually isn’t the remote battery. The receiver board on Ghost Controls units is powered by the main transformer, and when that starts to degrade, the receiver voltage drops and range collapses. We meter the transformer, and if it’s outside spec, we replace it. This fixes range problems far more often than a new remote does.
- Battery backup models: battery death after a grid flicker. Homes on the north side of Fort Worth near the Eagle Mountain corridor get their share of power interruptions, and Ghost Controls battery backup units work exactly as designed, but the batteries don’t last forever. When a gate starts running slow on battery or won’t close during an outage, the battery pack has reached end of life. We test the pack, and if it’s failing, we replace it with a deep-cycle replacement that matches the system’s charge profile.
Styles & brands we work with
Our Ghost Controls Gate Motor Repair Process
Here’s what a Ghost Controls repair looks like when you call Carver Gate Repair Fort Worth.
- 1
You call, a person answers. We ask what the gate is doing, what model you have, and whether the issue started suddenly or gradually. If Lonnie Burke is in the truck, he’ll tell you straight up what he suspects before anyone drives out.
- 2
We arrive in the scheduled window. Background-checked, uniformed technician. You know who you’re opening the gate for.
- 3
We diagnose in front of you. The tech opens the cover, checks the limit switches, meters the transformer and capacitor, and runs the gate through a cycle. No guesses, no parts cannon.
- 4
You get a written price. Before any work starts, we hand you a number for parts and labor. That number does not change when the job is done.
- 5
We repair, test, and clean up. We make the fix, run the gate through at least three full cycles, re-check the limits and force settings, and leave the area cleaner than we found it.
- 6
You get the guarantee in writing. Every Ghost Controls repair we do carries the 365-Day Done Right Promise. If the same issue comes back within a year, the second visit is free. No charge, no argument.
What Ghost Controls Gate Motor Repair Costs in Fort Worth
Here’s what we see in Fort Worth, based on the actual work we perform.
- Limit switch adjustment or replacement: $185 to $275
- Capacitor replacement: $160 to $230
- Receiver or transformer replacement: $220 to $340
- Gear set replacement on AXDP or R series arm: $290 to $420
- Full arm or motor replacement (parts and labor): $650 to $1,150
- Battery backup pack replacement: $240 to $380
What moves the price is the model you own, whether we’re replacing a component or the whole arm, and whether your gate is a standard single swing or a heavier custom gate that needs the VS series hardware. Every quote includes the written price up front. Call (817) 840-7067 for a free estimate, and we’ll tell you what the job costs before we touch a tool.
See the difference
Before
After
Before
After
Before
AfterWhy Fort Worth Homeowners Call Carver Gate Repair Fort Worth for Ghost Controls Work
Ghost Controls is one of the brands we know deeply, but it isn’t the only one. Our technicians are trained on LiftMaster, Mighty Mule, DoorKing, and six other gate motor brands, so when a Ghost Controls unit turns out to be better replaced than repaired, we can give you an honest comparison rather than forcing another Ghost Controls part into a gate that’s outgrowing it. That matters on older Fort Worth homes where a manually operated gate was converted to automation and the opener has always been undersized for the job.
Every job runs to The Garrison Standard. That means a written price before work starts, a background-checked and uniformed technician on site, and a written guarantee on every repair, good for a full year. It also means the phone gets answered by a real person, day or night. If a gate stops working at 11:00 PM and you need it closed for security, you call, we answer.
FAQs
If your Ghost Controls system is still under factory warranty, we recommend contacting Ghost Controls first for a warranty claim. As an independent Ghost Controls service provider, we’re not an authorized warranty station, and repairs we perform on a unit still under factory warranty could affect that coverage. Once the warranty has expired, which covers most of the systems we see in Fort Worth, we repair them without concern.
Yes. We stock the most common Ghost Controls parts locally, including limit switches, capacitors, gear sets, and transformers for the AXDP, TSS1, and R series. Less common parts, like VS series-specific boards, are typically sourced within a few days. We’ll tell you the parts timeline before you commit to anything.
The short answer: if the arm assembly and board are both still in good shape, repair almost always wins. A $300 limit switch or capacitor job buys you years more from a system that was working fine last week. We recommend replacement when the arm has stripped gears, the board has failed, and the gate itself is heavy enough that a bigger motor would serve you better long-term. We’ll show you the numbers for both and let you decide.
Most Ghost Controls repairs in Fort Worth are scheduled within 24 to 48 hours. If a gate is stuck open and security is a concern, we treat it as an emergency. Call (817) 840-7067 and explain the situation, and we’ll give you a straight answer on timing.
Yes. The 365-Day Done Right Promise is written on every Ghost Controls repair we perform. If the same problem comes back within a year from the date of service, we return and fix it at no charge. It’s part of The Garrison Standard, and it isn’t conditional on anything beyond the repair itself.
Contact Carver Gate Repair Fort Worth
If your Ghost Controls gate motor is acting up, call us at (817) 840-7067 for a free estimate. Tell us what it’s doing wrong, and we’ll tell you what it likely needs before we even roll a truck. We serve all of Fort Worth and the nearby areas, with background-checked, uniformed technicians and a written price on every job.
Written by Lonnie Burke, Owner, Carver Gate Repair Fort Worth at Carver Gate Repair Fort Worth, serving Fort Worth and nearby areas.