Ghost Controls Gate Repair Nationwide

Ghost Controls Gate Repair in Fort Worth: What to Know First

Ghost Controls gate repair in Fort Worth is work we handle regularly, and most common failures – a gate that won’t open, a keypad that stopped responding, an opener that runs but won’t move the gate – are back to working order within a single visit. As an independent Ghost Controls service provider, we’re not tied to factory service schedules, so we can usually get to you within 24 to 48 hours, and you’ll always get a written price before we touch a single bolt. If you own a Ghost Controls swing gate, slide gate, or the opener that runs it in Fort Worth, and something’s acting up, this page will show you exactly what’s going on, what it costs to fix, and who to call. Reach us at (817) 840-7067.

Call (817) 840-7067

How Ghost Controls Products Fail – and How We Fix Them

Ghost Controls builds residential gate operators that are simpler than most commercial-grade openers, and that simplicity has a downside: certain components wear out on a predictable schedule, especially in North Texas heat and clay soil. Here are the failures we see most often on Ghost Controls equipment in Fort Worth:

• AXDP-series arm slipping or losing travel (the “gate stops halfway” complaint). The AXDP is Ghost Controls’ flagship dual-swing arm operator, and its most common failure is the internal drive gear stripping after years of pushing against a gate that’s sagging at the hinge. The motor runs, but the arm loses purchase and the gate drifts or stops mid-swing. We check gate weight and hinge alignment first, then replace the gear set and reset the limit travel so it doesn’t fight itself again.
• TSS1 / TDS1 control board losing its mind after a storm. Fort Worth gets real lightning, and Ghost Controls boards are sensitive to power surges. The symptom owners describe is usually “the gate works fine, then one day the remote does nothing and the keypad just beeps.” That’s typically a fried relay or a corrupted auto-close setting. We bench-test the board, replace it with a factory-spec part when it’s dead, and add a surge protector at the power source so it doesn’t happen again next spring.
• Photo-eye (safety sensor) false obstruction trips in full sun. Ghost Controls uses a through-beam photo eye to keep the gate from closing on a person or vehicle. In the intense Texas sun, dust, spider webs, or a sensor that’s drifted out of alignment will trip the “obstruction” warning and hold the gate open. We clean, realign, and shield the sensor, then confirm the force settings are set so the gate will still reverse properly if a real obstruction passes through.
• Keypad and remote wall: the gate opens for one remote but not the other. Ghost Controls’ wireless keypads and remotes pair to the control board with DIP switches or a learn button, and they lose programming when the board loses power or when a new remote is added incorrectly. We reprogram all devices on-site and test them three times each, including the keypad mast, so you don’t watch a gate ignore you from the driveway.
• Battery back-up that only works for one cycle. Ghost Controls sells an optional battery kit, and we see Fort Worth homes where that battery is 5 or 6 years old and holds about enough charge to open the gate once, then trips the low-voltage alarm. We check the battery’s under-load voltage; if it’s done, we replace it with a matched unit and test the gate through a full open-close cycle on battery power alone.

One detail worth knowing: Ghost Controls equipment uses plastic sacrificial gears in some models to keep the motor from burning out if the gate hits something. That’s good engineering, but it means a gate that’s out of alignment will wreck the gear and leave you with a motor that runs but a gate that won’t move. We always check alignment before we replace a gear, because replacing the gear without fixing the reason it broke is how you end up paying for the same repair twice.

Our Ghost Controls Gate Repair Process

Every Ghost Controls job we take in Fort Worth follows the same sequence. You’ll know the plan before we start, and the price won’t change at the door.

1. 1
   You call, a person answers. We answer the phone 24/7, including weekends and holidays. We ask what the gate is doing (or not doing), note the model and any error codes, and schedule a visit that fits your day.
2. 2
   Diagnosis in the driveway. Lonnie Burke or one of our background-checked techs runs through the full system: board, arm or chain drive, limit switches, photo eyes, keypad, wall button, and the gate’s own hardware. We sketch what we find so you can see it.
3. 3
   Written price, before any work. You approve the exact number before we open a panel. If the diagnosis changes as we get deeper, we stop and tell you before we spend another dollar.
4. 4
   The repair itself. We use factory-spec Ghost Controls parts where the warranty depends on it, and quality aftermarket parts where the OEM part is overpriced for what it is. We’ll tell you which is which and why.
5. 5
   Test it three times. We run the gate through a full open-close cycle on remote, keypad, and manual release. We also check the auto-close timing, the force sensitivity, and the safety reverse.
6. 6
   Clean site, written guarantee. We sweep the area, repack our tools, and hand you a written guarantee on the repair – good for a full year under our 365-Day Done Right Promise. If it fails inside that window, the second visit is free.

What Ghost Controls Gate Repair Costs in Fort Worth

The cost of a Ghost Controls gate repair in Fort Worth depends on what failed, but you should know the numbers before you decide anything. Here’s what we charge for the jobs that come up most often:

• Service call + diagnosis (credited to the repair): $75 – $95
• Limit switch or travel reset: $160 – $220
• Control board replacement: $280 – $420, depending on the series
• Drive gear or arm gear replacement (AXDP or TSS1): $190 – $310
• Photo eye alignment or sensor replacement: $130 – $210
• Keypad or remote programming (all devices on-site): $90 – $140
• Battery back-up replacement: $180 – $350, depending on amp-hour rating
• Full opener replacement (Ghost Controls RGD series or newer): $800 – $1,850 installed

These are real numbers from actual Fort Worth jobs, not a website estimate generator. What moves the price: the model you have, whether we’re replacing a part or repairing it, and whether the gate itself contributed to the failure (a sagging gate always adds hinge work to a gear repair). The written price comes before work starts, and it does not move. Call (817) 840-7067 for an exact quote – estimates are free.

Why Fort Worth Homeowners Call Carver Gate Repair Fort Worth for Ghost Controls Work

Most of the people who call us have already had a bad experience with a contractor who didn’t show, or showed and then changed the price, or “fixed” the gate and vanished. We built Carver Gate Repair Fort Worth for those people. Every job runs on The Garrison Standard: a written price before work starts, a background-checked technician in uniform at the door, and a written guarantee on every repair, good for a full year. If the repair fails inside that year, we come back and make it right at no charge – no argument, no invoice.

We also work on the other motor brands in the same driveway: LiftMaster, Mighty Mule, and DoorKing, plus Viking, FAAC, BFT, Linear, and Elite. If your Ghost Controls unit goes down and the board is backordered, we can usually source a compatible part same-week through our network. Lonnie Burke runs the Fort Worth operation, and he’s got a notepad in his truck with sketches of what he found and what he fixed on every job we do – because you should know exactly what was wrong before you pay for it. Tell us what it’s doing wrong, and he’ll tell you exactly what it needs.

FAQs