Linear Gate Repair Nationwide

Linear Gate Repair in Fort Worth: What to Know First

Linear gate repair in Fort Worth typically runs between $180 and $850, depending on whether the issue is a failed limit switch, a worn drive gear, or a full operator replacement. We’re an independent Linear service provider, and most repair calls are resolved in a single visit because our technicians carry the common failure parts for Linear’s swing and slide gate operators on the truck. You’ll get a written price before any work starts, and every repair carries a full-year written guarantee.

Call (817) 840-7067

This page is for homeowners in Fort Worth whose Linear gate stopped opening, started reversing mid-cycle, or makes a grinding sound but won’t move. If that’s you, call (817) 840-7067 and we’ll walk through what you’re seeing before we ever roll a truck.

How Linear Products Fail – and How We Fix Them

Linear operators are solid machines, but after years of Texas heat, rain, and daily cycles, specific components wear out before the rest of the unit does. Here’s what we actually see on Linear repairs in Fort Worth, by model line and failure pattern:

• Limit switch failure on the Linear LDO series. The LDO swing gate operators rely on mechanical limit switches that control how far the gate travels before it stops. When these switches get caked with dirt, moisture, or just wear down from constant cycling, the gate slams into the open or closed stop instead of slowing down. Fort Worth’s fine clay dust accelerates this on gravel drives and properties near construction. We replace the switch assembly, set the limits, and cycle the gate ten times to confirm it stops clean on both ends.
• Capacitor failure on Linear SL and LS slide gate operators. A failing start capacitor is the most common reason a Linear slide gate hums but won’t move. The motor isn’t dead, it just isn’t getting the jolt it needs to start under load. We test the microfarad rating with a meter, and if it’s out of spec, we replace it with an OEM-rated capacitor, not a generic one that will cook itself in a Fort Worth August.
• Gearbox wear on the Linear MegaCode swing operators. The MegaCode line runs a worm-drive gearbox that handles the articulating arm. After years of use, the worm gear wears and the arm develops play, which makes the gate wobble through its arc and eventually bind. The honest repair is a gearbox rebuild or replacement, not spraying lubricant on it and calling it fixed. We pull the cover, inspect the gear faces, and show you what we found before we replace anything.
• Control board failure from lightning and power surges. Fort Worth gets serious thunderstorms, and Linear boards are sensitive to power spikes. A near-miss lightning strike on a fence-mounted operator can fry the board while the motor stays perfectly fine. We diagnose the board first, because replacing the motor when the board is the problem is a waste of your money. If the board is dead, we source a direct replacement and match the revision so your existing remote and keypad keep working.
• Photo eye and safety loop issues on Linear commercial slide gates. On Linear SLR and heavy-duty slide models, a gate that reverses for no reason is usually a dirty or misaligned photo eye, or a failing loop detector at the driveway. We clean and realign the eyes, test the loop frequency, and replace the detector if it’s drifted out of range. This is the difference between a gate that works and a gate that keeps reversing onto delivery trucks.

Our Linear Gate Repair Process

Here’s how a Linear repair goes from your first call to a closed job, written out so there are no surprises:

1. 1
   Call and describe the problem. You call (817) 840-7067, a live person answers, and we ask what the gate is doing, or not doing. We’ll get you on the schedule same day or next day, depending on your situation.
2. 2
   On-site diagnosis. The technician arrives in a Carver uniform, checks the operator, the limit switches, the capacitor, the board, the arm, and the gate hardware itself. If the problem is gate sag or a bad hinge, not the operator, we tell you that directly.
3. 3
   Written price, before any work. Once we know what’s wrong, we write up the repair with a firm price and go over it with you line by line. That number does not move unless you approve additional work.
4. 4
   The repair itself. We use OEM or OEM-spec Linear parts where it matters: control boards, limit switches, capacitors, and gear sets. For components like batteries and remotes, we’ll give you the choice between Linear-branded and quality aftermarket with an honest price difference.
5. 5
   Test and prove it. We cycle the gate a minimum of ten times under power, test the safety reversals, and confirm the limits are set correctly. We don’t leave until the gate operates like it should.
6. 6
   Written guarantee and a clean site. Every repair gets a written guarantee, good for a full year. If the same repair fails inside that year, we come back and make it right at no charge. The site is left the way we found it, or better.

What Linear Gate Repair Costs in Fort Worth

Repair pricing for Linear gates in the Fort Worth area breaks down by the part and the labor involved. Here are the ranges we typically quote, with the understanding that your exact price is confirmed in writing before any work begins:

• Limit switch replacement: $180 to $275, including the part and setup, on most LDO and MegaCode swing operators.
• Capacitor replacement: $120 to $190 on Linear SL and LS slide operators.
• Control board replacement: $325 to $550, depending on the model and whether we can source a current revision.
• Gearbox replacement: $400 to $685 on MegaCode swing operators when the worm gear is worn out.
• Full operator replacement (Linear slide or swing, installed): $1,200 to $2,800, depending on the operator size, gate weight, and whether new wiring or safety loops are needed.

What moves the price: access to the operator, the age and condition of the existing wiring, and whether the gate itself is out of alignment and needs separate hardware work. We’ll give you a free estimate with no obligation. Call (817) 840-7067 and we’ll send someone out to look at it.

Why Fort Worth Homeowners Call Carver Gate Repair Fort Worth for Linear Work

We’re gate specialists, not general contractors who fit gate work in between other jobs. Lonnie Burke and the crew have been working Fort Worth properties for years, and while plenty of companies can swap out a Linear controller, fewer know which specific revisions have board problems and which don’t, or which aftermarket arms hold up on a heavy iron driveway gate in this climate. Our technicians run on the Garrison Standard: background-checked, uniformed, and holding a written price before the first tool comes out. Every Linear repair is backed by our 365-Day Done Right Promise in writing, and if the same problem comes back inside a year, the second visit is free, no argument. We also work on LiftMaster, Mighty Mule, Ghost Controls, and DoorKing systems, so if you have more than one gate brand on the property, one call covers it. Tell me what it’s doing wrong, and I’ll tell you exactly what it needs.

FAQs