Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Fort Worth?
Our Gate Repair services in Fort Worth typically cost between $185 and $650 for most common fixes, with full gate motor replacement running $650 to $1,900 depending on the system. A standard service call including diagnosis and minor adjustment lands around $95 to $150, and most jobs can be completed the same day. We give you a written price before any work starts, so the number you approve is the number you pay.
Written by Lonnie Burke, Owner at Carver Gate Repair Fort Worth, serving the Fort Worth market since 2008.
Gate Repair Cost Breakdown (2026)
Here is what we’re seeing on the ground in Fort Worth this year. These are real ranges from the jobs our technicians run across Tarrant County – not national averages pulled from a database.
| Repair Type | Typical Cost Range | Notes |
|---|---|---|
| Service call and diagnostic | $95 – $150 | Applied toward the repair if you proceed |
| Hinge and weld repair | $185 – $420 | Heavier Fort Worth gates with sag often need both |
| Gate alignment and sag correction | $175 – $350 | Common on large driveway gates after soil shift |
| Limit switch replacement | $145 – $285 | Fixes gates that stop short or overrun |
| Loop detector replacement | $195 – $380 | Solves gates that won’t open for exiting vehicles |
| Circuit board repair/replacement | $250 – $550 | Depends on brand and board availability |
| Gate motor replacement (operator) | $650 – $1,250 | Swing or slide operator, parts and labor included |
| Full gate installation | $1,900 – $4,800 | Depends on gate type, material, and driveway width |
| Photocell and safety sensor repair | $135 – $290 | Common after a Fort Worth hail or wind storm |
| Remote and keypad programming | $65 – $150 | Often bundled with a service call |
What moves a price up or down? The gate’s weight, the condition of the existing hardware, whether the post footings are stable, and which motor brand is installed all matter. A LiftMaster or FAAC operator generally has better parts availability in Fort Worth than some older or discontinued units, which can shorten a repair. A gate that’s been neglected for years tends to need three small fixes instead of one, because wear compounds.
If you’re weighing repair against replacement, use this rule of thumb: if the cost to fix exceeds 50% of a new gate installed, replacement is usually the smarter money. A technician can walk you through that math on site.
What Affects Gate Repair Pricing in Fort Worth
- Gate type and weight. A 14-foot iron driveway gate with steel posts is a different job than a lightweight pedestrian gate. Swing gates put more torque on hinges and operators; slide gates strain rollers, chains, and track. Heavier gates mean more labor and beefier components.
- Motor brand. We work on nine gate-motor brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Parts pricing differs by brand. Some boards run $180; some run $400. The good news: we keep the common parts on the truck.
- Soil movement and post condition. Fort Worth’s clay-heavy soil expands and contracts with moisture. That heaving is why we see so many gates go out of plumb in neighborhoods like Ridglea Hills, Wedgwood, and over toward Benbrook. When a post shifts, the gate sags, and the operator works harder until something fails. Fixing the gate without addressing the post means the repair won’t hold.
- Access and layout. A gate at the back of a long driveway off a busy street in south Fort Worth may require different staging than a front gate in a North Richland Hills-style subdivision. Narrow easements, limited swing clearance, and fence proximity all factor in.
- Electronics and safety sensors. If the problem is mechanical only – a hinge, a wheel, a chain – a repair is straightforward. If the loop detector, photocell, or limit switch is involved, diagnostic time goes up and so does the price. These safety components aren’t optional; a gate that doesn’t reverse when it should is a hazard, and we won’t leave a gate running without them functional.
- Age of the system. Some Fort Worth homes still run operators from the early 2000s. We can often source parts for older units, but when a board is discontinued, a retrofit or new operator becomes the fix. That changes the quote significantly – which is exactly why we put it in writing before touching anything.
Can You Fix a Gate the Same Day in Fort Worth?
Most repair jobs, yes. Hinge & Post Repair, limit switch adjustments, operator swaps, and sensor repairs are generally same-day work when parts are on hand. We dispatch background-checked, uniformed technicians across Fort Worth every day, and our phones are answered by a live person 24/7 – including weekends and holidays. If you call in the morning, you have a good chance of seeing a technician by afternoon. If the gate is stuck closed and your car is trapped inside, we treat that as a priority and work it into the schedule the same day.
What Are the Most Common Gate Problems We See in Fort Worth?
Every market has its signature issues. Fort Worth’s combination of clay soil, summer heat, and occasional violent storms produces a fairly predictable failure pattern. Here’s what our technicians encounter most:
Sagging gates and failed hinges
Clay soil moves. Posts shift, gates drop, and the latch no longer lines up. By the time a homeowner notices the sag, the hinge bearings have usually been wearing unevenly for months. Fixing the gate before the post pockets crack completely is much cheaper.
Operator failure from heat and power surges
Fort Worth summers push 100°F routinely. Circuit boards and motors that sit in a metal housing in direct sun endure real stress. Power surges during summer storms can also fry a control board. If your gate opened fine in May and won’t budge in August, heat or surge damage is often the culprit.
Loop detector failure
The loop detector is the buried sensor that tells the gate a car is waiting. When it fails, the gate won’t open automatically for exiting or entering vehicles. We see this most in driveways where concrete has cracked or been re-poured over the loop wire.
Limit switch drift
A limit switch tells the motor where to stop. When it drifts, the gate overruns the opening or stops short of the closed position. Sometimes it’s a simple adjustment; if the switch itself is failing, replacement is the fix.
Weather-damaged sensors
Photocells and edge sensors take direct hits from hail and flying debris during spring storms. A broken photocell usually means the gate refuses to close, for safety reasons. That’s by design – but it means a repair call until the sensor is replaced.
Gate Motor Replacement: What to Expect
When a motor has failed beyond economical repair, replacement is the right call. In Fort Worth, a new swing or slide operator with professional installation typically runs $650 to $1,250, depending on the gate’s weight class and the operator type. A heavy-duty commercial slide operator on a long driveway gate in areas like Aledo or Weatherford can push higher.
Here’s the step-by-step of how we handle a motor replacement:
- Call and dispatch. You call (817) 840-7067. A live person answers, asks about your gate type and symptoms, and schedules a technician.
- On-site diagnosis. The technician checks the operator, limit switches, gear condition, and power supply. You get a written price before any work starts – the number doesn’t move when the job is open.
- Parts matched to your system. We match the replacement to the gate’s weight, duty cycle, and your existing controls. We stock and train on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so the operator is matched to what’s already installed.
- Installation and calibration. The technician removes the old operator, installs the new one, calibrates open and close limits, and tests force settings so the gate reverses properly on obstruction.
- Cleanup and walkthrough. The work site is left clean. The technician walks you through operation, gives you the written guarantee on the repair, and makes sure remotes and keypads are programmed.
If the repair fails inside the guarantee window, the second visit is free. That’s the 365-Day Done Right Promise, and it’s in writing on every job. No charge, no argument.
How to Save on Gate Repair
Gate repair doesn’t have to be a shot in the dark. Here’s how to keep the total bill down without cutting corners on safety:
- Don’t ignore small problems. A squeaking hinge or a gate that’s slightly out of level gets worse. Early fixes are usually under $300; deferred fixes become operator replacements that run four times that.
- Keep the track and rollers clean. For slide gates, dirt and debris in the track force the motor to work harder. A five-minute hose-down every month extends the life of rollers, chain, and operator.
- Check posts annually. If a post is leaning or the concrete collar is cracked, address it before the gate sags and the hinge welds fail.
- Test safety sensors regularly. Wave an object in front of the photocell while the gate is closing. If it doesn’t reverse, call a technician. Catching a sensor issue early keeps a small electrical repair from becoming a full gate failure.
- Get a written quote and know what it covers. The free estimate we give you before any work starts protects you from price creep. Call (817) 840-7067 for an exact number – here’s more about our gate repair services in Fort Worth.
FAQs – Gate Repair Cost
How much does it cost to fix a gate that won’t open?
Between $95 and $550 depending on the cause. A simple limit switch adjustment runs about $145 to $285. A failed circuit board replacement runs $250 to $550. The diagnostic fee tells you which one you’re dealing with – call (817) 840-7067 and we’ll get a technician out to pinpoint it.
Is it cheaper to repair or replace a gate motor?
If the motor is less than 5 years old and the failure is a board, limit switch, or capacitor, repair is usually cheaper – typically $150 to $550. If the operator is 10+ years old or has internal gear failure, replacement at $650 to $1,250 often costs less over the next five years than repeated repairs on a tired unit.
How much does a gate motor replacement cost in Fort Worth?
A new swing or slide gate operator typically runs $650 to $1,250 installed, including parts, labor, calibration, and testing. The brand and gate weight drive the number. We’ll give you a written price before any work starts.
How much is a service call for gate repair in Fort Worth?
Expect $95 to $150 for the trip and diagnostic. That money is applied toward the repair if you approve the work. It’s how we make sure you’re not paying for guesswork.
Can you fix a gate that’s off its hinges?
Yes. Hinge and weld repair runs $185 to $420 in the Fort Worth market, depending on the gate’s weight and whether the post needs reinforcement. Lock Repair is also available if your latch or locking mechanism has failed. This is one of the most common repairs we do, especially in neighborhoods with older iron gates and shifting clay soil. Call (817) 840-7067 for an exact quote – estimates are free.
Why The Garrison Standard Matters for Your Gate Repair
Gate work has a trust problem. Homeowners have been burned by no-shows, by quotes that grew once the gate was pulled apart, by technicians who left beer cans in the flower bed. We built Carver Gate Repair to run differently, and the Garrison Standard is the backbone of it.
Here’s what that means in practice. Every technician who steps onto your property is background-checked and uniformed. You’ll know who’s at your gate before you open it. Every job gets a written price in advance, so the number you approve is the number you pay – full stop. Every repair carries a written guarantee, good for a full year from the date of service. If it fails inside that window, the second visit is free. That’s the 365-Day Done Right Promise, and it’s not a marketing line. It’s the floor.
Phones are staffed by a live person 24 hours a day, seven days a week, including holidays. Call at 3 a.m. if your gate is stuck and a person answers. That’s not a perk; it’s what a gate company should do.
The Garrison Standard has been the operating rule since 2008, and every Carver location runs the same playbook. Part of the Garrison Partners family, we focus on one thing: gates. Not fences, not decks, not landscaping. Gates and gate motor systems. When a specialist works on one system every day across nine brands, the diagnosis is faster and the fix is right the first time.
Was this page useful? Here’s the home page for more about how we work.
Pricing reflects the Fort Worth market as of 2026. Carver Gate Repair Fort Worth offers free estimates – call (817) 840-7067.
Written by Lonnie Burke, Owner at Carver Gate Repair Fort Worth, serving Fort Worth since 2008.
What Our Customers Say
"Photo eyes cleaned and aligned. Gate stops for the dog like it should."
- Henry B."Added a battery backup so the gate works during a power outage. Easy to use."
- Mitch L."Swing gate arm snapped. They replaced the actuator and tested the safety reverse. Fair price."
- Angela P.