Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Bedford
Gate repair in Bedford usually costs between $180 and $650 depending on what failed. A hinge re-weld or post reset runs $180 to $400, a control board replacement on a legacy operator lands between $350 and $650, and a full motor swap on an older swing gate typically starts around $850. We dispatch background-checked, uniformed technicians to Bedford every weekday, and the phone at (817) 840-7067 is answered by a live person around the clock. If your gate is dragging, jammed, or running without its safety photocell, you’ll get a written price before anything comes apart.
Why Carver Gate Repair Fort Worth Is Bedford’s Preferred Gate Repair Company
Bedford’s housing stock presents a different set of problems than the newer subdivisions nearby. Most of our calls here come from homeowners whose gates were installed when the house was built, meaning 1960s through 1980s ornamental iron and chain-link work that has been through four decades of North Texas summers and at least a few hard freezes. Our technicians arrive already knowing that a Bedford gate post is likely set in old concrete that has shifted, and that the hinges may be welded rather than bolted. That changes the repair approach before the first tool comes off the truck.
Our Gate Repair team works to The Garrison Standard, which means every Bedford job gets a written price before work starts and a written guarantee good for a full year. Lonnie Burke runs the operation and holds every technician to that standard. We don’t send a different sub each time. The same process applies on every call, whether it’s a Gate Motor Repair in Bedford or a rusted hinge post that needs custom fabrication.
Styles & brands we work with
Wrought Iron Gate Repair in Bedford
Wrought iron gate repair in Bedford is the most common specialty call we field, and it rarely looks like what a homeowner expects. The gate leaf usually isn’t broken. What fails is the connection point: a hinge weld that has cracked through, a bolt hole that has ovaled out from wind stress, or a post that has leaned just enough to drop the latch side onto the driveway. In Bedford’s older neighborhoods, where many gates were hung before modern fabrication standards, hinge plates were often welded directly to steel posts set in shallow concrete. Once that concrete shifts during a freeze-thaw cycle, no amount of hinge tightening straightens the gate.
Repair runs $180 to $400 for most hinge and realignment work on wrought iron. If the post itself has moved, the post has to be re-set or an offset hinge plate fabricated to match the original bolt pattern. That runs toward the upper end of the range but keeps the original gate leaf in service, which is almost always the cheaper answer compared to a new iron gate.
Hinge and Post Repair
When a wrought iron gate drags on the driveway, the problem is usually at the hinge post, not the gate leaf. In Bedford, slab footings poured forty or fifty years ago have often shifted enough that a once-straight hinge pin now sits at an angle. We reset the post when the concrete allows it, or fabricate a weld-on hinge plate that compensates for the shift without touching the brick columns beside the gate.
Gate Realignment
A gate that sags but still swings usually needs realignment: re-plating the hinge, adjusting the latch strike, and sometimes shimming the bottom hinge to lift the latch side. This is a two-hour job in most cases and costs between $180 and $300 in Bedford, assuming the hinges themselves aren’t torn.
Metal Gate Repair in Bedford
Metal gate repair in Bedford covers the full range of steel and aluminum work we see, from rust-through on the bottom rail to stress cracks radiating from old hinge welds. Bedford’s particular climate works against metal gates in two directions. Summer heat expands the steel and puts constant pressure on weld points, and the freeze-thaw cycles in winter let moisture seep into micro-cracks, freeze, and widen them. A crack that’s invisible in June can open up a quarter inch by February.
Repair cost for typical metal gate failures runs $180 to $450. Weld repairs on a cracked hinge plate fall at the low end. Rust-through on a gate bottom rail, which is common on 1970s steel gates that were never powder-coated, runs toward the middle. If the rust has spread into the post as well, the job may involve cutting the post at ground level and setting a new sleeve, which lands near the top of the range.
Weld & Rust Repair
Weld cracks at the hinge post account for a large share of our Bedford repair work. Wind loads on an eight-foot ornamental gate put enormous stress on those welds, and forty years of that stress eventually wins. We grind the old weld out, re-weld with proper penetration, and often add a gusset plate so the same crack doesn’t return next season.
Lock Repair
Gate locks on older Bedford properties take a beating from both weather and misalignment. When the gate sags even half an inch, the lock throw no longer lines up with the strike, and eventually the internal mechanism binds. We repair or replace the lock, then correct the sag so the new hardware isn’t broken within a year.
Trusted Brands We Service in Bedford
We work on all nine of the brands we carry parts for, and in Bedford the mix runs heavily toward DoorKing, Elite, and Mighty Mule equipment, with Ghost Controls showing up on newer installs. DoorKing operators from the 1980s and 1990s are still common in Bedford’s older subdivisions, and many of them are still running original control boards. We keep the most frequently needed boards, limit switches, and photocells in local stock so a Bedford repair doesn’t wait on a parts truck from across the metro.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Repair Problems We See in Bedford Homes
- Hinge welds cracking at the post. Freeze-thaw cycles and wind loads on large iron gates concentrate stress right at the hinge weld. Once a crack starts, the gate leaf drops and drags within a season.
- Operators running without entrapment protection. Bedford has no citywide gate safety inspection program, so many legacy operators on 1960s to 1980s lots still run without a photocell or edge sensor. A failing operator can close on a vehicle or a child, and homeowners often don’t know the protection is missing until we point it out.
- Shifted concrete posts. Footings poured decades ago have moved enough that the hinge pin is no longer plumb. A straight hinge replacement is impossible on these jobs; the post has to be reset or an offset hinge fabricated.
- Rust-through on bottom rails. Bedford’s summer heat and winter moisture work the bottom rail of a steel gate hard, especially where the rail meets the pickets. By the time rust shows through, the section usually needs cutting out and replacing.
Pricing for Gate Repair in Bedford, TX
Most Bedford gate repairs fall between $180 and $650. Hinge work and realignment run $180 to $400. A replacement control board on an older DoorKing or Elite operator lands between $350 and $650. A full operator swap starts around $850 and goes up based on the model and whether a new loop detector or safety edges are needed. What moves the number is the condition of the post: if the concrete footing has shifted, the repair is no longer a simple hinge job. Every Bedford customer gets a written price before the work starts. Call (817) 840-7067 and we’ll give you a real number, not a range that grows once the gate is open. The estimate is free.
We Also Serve Cities Near Bedford
Our Bedford crews also cover Southlake, Haltom City, Fort Worth, and Mansfield on the same schedule. If your property sits close to the Bedford line but uses a Haltom City or Fort Worth mailing address, the service area is the same and the written-price policy doesn’t change.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Bedford
The heat isn’t bending the gate. It’s exposing a post or hinge problem that was already there. In Bedford’s summer heat, the steel gate leaf expands slightly and transfers more load onto the hinge post. If that post is set in old concrete that has shifted, or if a hinge weld has a hairline crack that’s been hiding all spring, the added thermal stress is what finally makes the gate drop and drag. The fix is at the post or the hinge, not in the gate leaf itself. Call (817) 840-7067 and we’ll find where the movement actually starts.
Usually yes, as long as the operator has a functioning accessory input on its control board. Most 1980s-era DoorKing and Elite boards have terminals for an external entrapment sensor, even if the original install never used them. If the board predates UL 325 entrapment requirements, a retrofit may require replacing the board as well, which runs $350 to $650 in Bedford. Either way, adding a photocell to a legacy operator is a fraction of the cost of replacing the whole operator, and it brings the gate up to current safety expectations.
Yes, and that’s a job we do regularly in Bedford’s older subdivisions where hinges were welded directly to steel posts at install. The torn hinge has to be cut and ground off, then a new hinge plate is fabricated to match the original bolt pattern or welded back in place with better penetration and often a gusset plate for reinforcement. It’s a $180 to $400 repair in most cases. Call (817) 840-7067 for a written price before the work starts.
If the failure is a limit switch, a capacitor, or a control board, repair usually makes sense, and costs $200 to $650 in Bedford depending on the part. If the motor itself is seized, the gearbox is stripped, and the board is original from the 1980s, a replacement operator usually costs less than repairing all three at once. The giveaway on an older Bedford operator is when two or more independent failures show up inside the same year. At that point, we’ll show you the written repair number next to the replacement number and let you choose without a push in either direction.
Yes. It usually breaks the hinge weld, not the gate itself. When moisture seeps into a micro-crack in a weld during a warm day and then freezes the next night, the ice expands inside the crack and forces it open further. After enough Bedford winters, a hairline crack becomes a torn hinge plate and the gate leaf drops onto the driveway. That’s the exact failure pattern we see most in the older neighborhoods around Shady Brook and along Harwood Road.
Written by Lonnie Burke, Owner at Carver Gate Repair Fort Worth, serving Bedford and the surrounding area.