Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Repair Cost in Fort Worth?
Most Gate Repair jobs in Fort Worth cost between $185 and $575, with a typical service call running $75 to $125 and parts billed separately. A full gate motor replacement usually lands between $650 and $1,400 depending on the operator and access. Those are real numbers for this market: Fort Worth homeowners regularly report total repair bills in that range when working with a licensed gate specialist rather than a general handyman.
Carver Gate Repair Fort Worth gives every customer a written price before any work starts, so the number you approve is the number you pay. Lonnie Burke and our technicians work exclusively on gates and gate motors, which means we quote accurately from the first visit instead of discovering “surprises” after the job is open.
Gate Repair Cost Breakdown (2026)
Here are the line-item prices we see across Fort Worth, from Wedgwood to Saginaw. The ranges reflect parts plus labor for a typical single-family driveway gate.
| Repair Type | Typical Cost Range (Parts & Labor) |
|---|---|
| Service call / diagnosis | $75 – $125 |
| Limit switch replacement | $165 – $260 |
| Loop detector replacement | $225 – $380 |
| Hinge repair or replacement | $195 – $450 |
| Chain or belt replacement | $140 – $310 |
| Circuit board replacement | $285 – $520 |
| Gate wheel or roller repair | $120 – $240 |
| Swing arm operator repair | $350 – $700 |
| Full gate motor replacement | $650 – $1,400 |
| Gate realignment / welding | $180 – $475 |
What pushes a job toward the top of a range is usually access and time. A gate at the end of a long easement off Old Granbury Road takes longer to reach than one in a compact Ridglea Hills lot. A welded steel gate that has sagged for two years needs more labor than a single Hinge & Post Repair on a gate that was serviced last season. Parts matter too: a LiftMaster circuit board costs more than a generic limit switch, and a Viking swing operator is a heavier unit than a Mighty Mule used on a lightweight farm gate.
Labor in Fort Worth generally runs $85 to $110 per hour for a gate specialist. Most repairs take one to three hours on site. That is the honest math behind every number above.
What Affects Gate Repair Pricing in Fort Worth
- Gate type and weight. A heavy wrought-iron swing gate in Arlington Heights takes more labor and stronger hardware than a light aluminum slide gate in Benbrook. Weight determines hinge wear, operator strain, and how many technicians the job needs.
- Motor brand and age. We work on nine major brands including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Older or discontinued boards sometimes cost more because parts are scarcer, not because the labor is harder.
- Access to the gate. Some Fort Worth properties, especially in areas like Walsh Ranch or along the Chisholm Trail corridor, have long driveways, uneven terrain, or gates set back from the street. Every extra trip from the truck to the gate adds time.
- Time of year. Fort Worth summers with weeks above 100 degrees accelerate wear on exposed wiring, solder joints, and plastic gear housings. We see a spike in heat-related failures from July through September, and that demand can push scheduling, though our pricing stays flat.
- Electrical vs. mechanical failure. A gate that stopped because a limit switch failed is a straightforward fix. A gate that stopped because the operator was underpowered from day one is a design problem that may require upgrading the motor, which changes the price entirely.
- Whether the gate was installed correctly. This is the quiet cost driver. In Fort Worth's newer subdivisions like Chisholm Ridge, some gates were installed by fence companies that did not set proper clearances. A misaligned install shortens the life of every component. Repairing the underlying install error costs more than fixing the symptom.
How to Save on Gate Repair
The most expensive gate repair is the second one. A cheap fix that holds for six months costs more than a proper repair that holds for five years. That said, there are legitimate ways to keep costs down without cutting corners.
First, catch problems early. A gate that scrapes the ground, groans, or hesitates for half a second before opening is telling you something. Every week you ignore a strained hinge or a dragging wheel means more wear on the rest of the system. Small fixes in the $150 to $300 range often prevent motor replacements in the $800 to $1,400 range.
Second, know your motor brand before you call. LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, Mighty Mule. The model number is on a sticker on the operator itself. Having that ready shortens diagnosis time, and it tells us which parts to bring on the first trip. That saves you a return visit.
Third, get a written price before work starts. That is not a negotiation tactic; it is a basic standard. Carver Gate Repair Fort Worth provides a written price on every job, before any parts are ordered or any labor begins. The number does not move at the door.
Fourth, ask about the guarantee. Our repairs carry a written 365-day guarantee. If the same repair fails inside that window, we return and make it right at no charge. That is the part that actually saves money over time: you pay once, not twice.
For an exact quote on your gate, call (817) 840-7067. Estimates are free, and a real person answers the phone.
Typical Gate Repair Process in Fort Worth
Here is exactly how a repair call works with us. Knowing the process helps you understand what you are paying for at each step.
- You call (817) 840-7067. A live person answers, day or night. We ask about the gate type, motor brand, and symptom. That conversation determines which parts and tools the technician loads before heading out.
- Technician arrives in a uniform. Every Carver technician is background-checked and wears company identification. You know who is on your property before they step out of the truck.
- Diagnosis and written quote. The technician inspects the gate, gate motor, hinges, track or swing arm, and electrical connections. Then you get a written price for the full repair. Nothing starts until you approve it.
- Repair. Most jobs are completed on the first visit. Common repairs include replacing limit switches, loop detectors, hinge assemblies, chains or belts, circuit boards, wheels, and swing arms.
- Clean site and walkthrough. The work area is left as it was found. The technician runs the gate through several open-and-close cycles with you watching and explains what was replaced and why.
- 365-Day Done Right Promise. Every repair is backed in writing for a full year. If the same repair fails, we return and fix it free.
That last step is the Garrison Standard at work. It has been the operating rule for Carver Gate Repair since 2008, and it applies on every job in Fort Worth.
Common Fort Worth Gate Repair Scenarios
These examples reflect real calls our technicians handle in the Fort Worth market, with actual working conditions that shape the final bill.
Gate Won't Open or Close at All
In Fort Worth neighborhoods with older electrical service, like parts of Como or White Settlement, a gate that suddenly goes dead is often a tripped breaker or a failed surge protector after a thunderstorm. Fort Worth gets intense spring storms, and a lightning strike a block away can take out a gate circuit board. A circuit board replacement typically runs $285 to $520. If the whole operator is dead, that is a motor replacement at $650 to $1,400.
Gate Opens Halfway Then Stops
That is usually a limit switch issue. The limit switch tells the motor when to stop. When it fails, the motor loses its stopping point and behaves erratically. On most brands, including LiftMaster and BFT, the switch itself is a $30 to $60 part, with total repair cost landing between $165 and $260 including labor.
Gate Scrapes the Ground or Drags
This is common in Fort Worth areas with expansive clay soil. The ground moves. A gate that cleared easily in January scrapes by August because the soil swelled. Repair usually means adjusting hinges, raising the gate, or replacing a wheel. Expect $120 to $450 depending on whether welding is required.
Gate Remote Stops Working
Before assuming the motor is bad, we check the loop detector and the receiver board. A failed loop detector, common on properties with heavy clay soil and constant ground shifting, costs $225 to $380 to replace. A failed receiver is often handled by replacing the circuit board at $285 to $520.
Gate Opens By Itself or Won't Stay Closed
This is a safety concern. In some cases it is a faulty loop detector sensing phantom vehicles. In others it is a misaligned photo eye or a shorted control wire. These repairs generally run $185 to $380. If your gate is opening on its own, call (817) 840-7067 the same day. A gate that opens without command is not just a nuisance; it leaves your property exposed.
FAQs About Gate Repair Cost in Fort Worth
How much does a gate motor replacement cost in Fort Worth?
A gate motor replacement in Fort Worth typically costs between $650 and $1,400 installed. The range depends on the operator type (slide vs. swing), brand (LiftMaster, Viking, BFT, DoorKing, and others), and whether the existing mounting hardware can be reused. Call (817) 840-7067 for a written quote specific to your gate.
Is it cheaper to repair or replace a gate motor?
Repair is cheaper in most cases. If the repair cost is under 50% of a new motor's price and the motor is under eight years old, repair usually makes sense. A circuit board replacement at $285 to $520 beats a $1,000 motor replacement. But if the operator is 12-plus years old and parts are discontinued, replacement is the better financial decision. We will show you the numbers for both options before you decide.
How much is a service call for gate repair in Fort Worth?
A gate repair service call in Fort Worth runs $75 to $125. At Carver Gate Repair, the service call includes full diagnosis and a written quote for the repair. If you proceed with the repair, the service call fee is applied toward the total job.
How fast can you repair a gate in Fort Worth?
Most Gate Repair Near Me in Fort Worth, TX calls are completed same-day or next-day. We dispatch technicians across Fort Worth daily, from White Settlement to Benbrook to Richland Hills. Emergency calls, like a gate stuck open, are prioritized. Call (817) 840-7067 and a live person will schedule you. We answer the phone 24 hours a day, every day of the year.
Do you charge extra for weekends or holidays in Fort Worth?
No. Our rates are the same regardless of the day or hour. You will get a written price before work starts, and that price does not change because it is Saturday or 10 p.m. on a holiday. The Garrison Standard is the same every day.
Does Carver Gate Repair offer a guarantee on Fort Worth repairs?
Yes. Every repair carries a written 365-day guarantee. If the same repair fails inside that year, we return and fix it free. That guarantee is in writing on every invoice, no exceptions.
Key Takeaways: Gate Repair Pricing in Fort Worth
- Typical total cost: $185 to $575 for most repairs, with motors running $650 to $1,400.
- Service call: $75 to $125, applied toward your repair if you proceed.
- Hourly labor: $85 to $110 per hour, with most jobs done in one to three hours.
- Biggest cost drivers: gate weight, motor brand, access difficulty, and heat-related electrical wear.
- Best saving strategy: fix small issues early before they kill the motor.
- What you should demand: written price before work, background-checked technician, full-year written guarantee.
Why Fort Worth Homeowners Call Carver Gate Repair
Every Carver Gate Repair location runs on the Garrison Standard. That is not a marketing slogan. It is a written operating code: background-checked, uniformed technicians on every call. Written pricing before any work begins. A written 365-day guarantee on every repair. A live person answering the phone 24/7. Free second visit if a repair fails within the guarantee window.
Since 2008, the Garrison Partners family has held every location to this standard. Carver Gate Repair Fort Worth is part of that family, led locally by Lonnie Burke. We work exclusively on gates and gate motor systems across nine major brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We do not do fences, roofs, or doorbells. Gates are the whole job.
That focus is why a homeowner in Tanglewood, Ridglea, or Saginaw can call us and get a straight answer on cost, timing, and the exact fix needed. If you are tired of no-shows and prices that creep up after the work starts, you will notice the difference on the first call.
If your gate is acting up, call (817) 840-7067 now. We answer around the clock, and the estimate is free. For more on what we do, see our Gate Repair in Fort Worth page or head back to the home page to learn more about the Garrison Standard.
Contact Carver Gate Repair Fort Worth
Ready for a written estimate? Call (817) 840-7067. A live person picks up, day or night, weekends included. We will ask a few questions about your gate, schedule a visit, and send a background-checked, uniformed technician with the right parts on the first trip. Every repair carries a written price before work starts and a 365-day guarantee after it ends.
Pricing reflects the Fort Worth market as of 2026. Carver Gate Repair Fort Worth offers free estimates – call (817) 840-7067.
Written by Lonnie Burke, Owner at Carver Gate Repair Fort Worth, serving Fort Worth since 2008.
What Our Customers Say
"Keypad and remotes set up fresh for the whole neighborhood. Done cleanly and quickly."
- Chris W."Straight answers on whether to repair or replace the operator. Repair was the right call."
- Wanda F."Slide gate wasn't opening fully. Veteran tech found a worn drive chain and a misaligned limit. Fixed both in one visit."
- Don H.