Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterGate Realignment in Fort Worth, TX
A gate that drags, sticks, or won’t latch isn’t just annoying. It wears out hinges, burns up motors, and leaves your driveway open to whatever wanders in. Gate realignment in Fort Worth typically costs $150 to $425 depending on what has shifted and how heavy the gate is. Carver Gate Repair Fort Worth handles realignment as a same-visit fix in most cases, and we put the price in writing before any work starts. If you’re dealing with a gate that has started scraping the ground or refusing to close, call us at (817) 840-7067 and we’ll send a background-checked technician to take a look. For a broader look at what we handle, see our Gate Repair page.
Fort Worth’s clay soil is the usual culprit behind misaligned gates. Summer heat bakes the ground dry and it contracts. Spring rain swells it back. Over a few seasons, gate posts lean, hinges settle, and a gate that once swung clean now binds against the latch post or drags a groove into the driveway. In neighborhoods like Ridglea Hills, Arlington Heights, and Wedgwood, we see the same pattern repeat year after year with both swing and slide gates.
Realignment is not a patch job. It means resetting the gate’s geometry: post position, hinge wear, operator travel, and latch engagement. Done right, it extends the life of the motor and the gate itself. Done wrong, the gate works for a week and sags again.
We work on gates paired with Ghost Controls, DoorKing, Elite, and Mighty Mule operators, among others. The motor matters during realignment because an operator that has to push a binding gate draws more current, trips its limit switches early, and fails sooner than it should.
When You Need Gate Realignment
Most homeowners call us because they noticed one of these. Each one points to a geometry problem that only gets worse if left alone.
- The gate scrapes the driveway or drags through gravel. In Fort Worth’s freeze-thaw winters and dry summers, post movement of even half an inch shows up as a visible scrape mark. Scraping means the gate’s weight is no longer carried by its hinges alone.
- The latch misses the strike plate or only catches partway. This is the most common security complaint we hear in the Ryan Place and Mistletoe Heights areas. A gate that looks closed but isn’t latched can be pushed open by hand.
- The gate has a visible lean or the gap at the hinge side has widened. Sight down the top rail. If the gap between gate and post isn’t consistent from top to bottom, the post or hinge has moved.
- The motor strains, hums, or reverses mid-cycle. Operators from DoorKing and Mighty Mule have obstruction detection built in. A misaligned gate trips that sensor because the operator reads the binding as an obstacle.
- You hear a popping or creaking at the hinge when the gate moves. That sound is metal under uneven load. Ignoring it means a hinge pin eventually shears or a weld cracks.
- The gate slams shut or won’t stay open on its own. Swing gates should settle gently against the close stop. If it picks up speed near the end of travel, the gate is no longer level and gravity is doing the closing.
Our Gate Realignment Process
Every realignment job follows the same order of operations. It’s the Garrison Standard applied to the physical geometry of your gate. No shortcuts, no “good enough.”
- Inspect and measure. We check post plumb with a level, measure hinge sag, and observe a full open-close cycle with the operator connected. On slide gates, we check rail level and roller wear. On swing gates, we check hinge pin wear and the gap between gate and latch post.
- Identify what moved. Sometimes it’s the hinge post. Sometimes it’s the gate frame itself. Sometimes the operator’s limit switch settings are out of sync with the gate’s true travel. We find the root cause before touching anything, because the fix is different for each.
- Correct the alignment. This may mean re-shimming hinges, resetting a post in fresh concrete, adjusting roller brackets on a slide gate, or re-leveling the gate frame. For welded steel gates, we grind and re-weld worn hinge points. For aluminum gates, we replace worn hinge bushings rather than bending the frame.
- Re-set the operator. Once the gate moves freely by hand, we adjust the operator’s limit switches, force settings, and obstruction sensitivity on the installed motor, whether that’s a Ghost Controls, Elite, or another brand. The operator should never work harder because of a geometry problem.
- Adjust the latch and stops. The gate should close square against the stop, and the latch should engage without being forced. We adjust the strike, add shims where needed, and verify the lock functions.
- Cycle test and walk-through. We run the gate through at least ten full cycles with the operator connected, then show you what was adjusted and why. You’ll get a written report of the work and the terms of the guarantee before we leave.
Gate Realignment Pricing in Fort Worth
Realignment pricing depends on gate type, gate weight, and how far things have moved. For a detailed breakdown, see our How Much Does Gate Repair Cost in Fort Worth, TX? (2026 Price Guide). Here are the ranges we quote most often in the Fort Worth area.
| Gate Type | Typical Realignment Cost | What’s Usually Involved |
|---|---|---|
| Single swing gate (residential) | $150 – $275 | Hinge adjustment, post shimming, latch reset, operator re-setting |
| Double swing gate | $275 – $425 | Both leaves leveled, center stop adjusted, both operator arms re-set |
| Slide gate (residential) | $225 – $375 | Roller replacement, rail leveling, limit switch re-set |
| Post reset (concrete work) | $75 – $150 per post | Digging, re-setting post in concrete, re-mounting hinges |
| Hinge replacement (heavy steel gate) | $50 – $90 per hinge | Removal of worn hinge, weld or bolt new hinge, re-align gate |
Those are the numbers you’ll see on a written quote before we start. The price doesn’t move once the work begins. If a hinge breaks during the job and we have to replace it, you’ll know the cost of that hinge before we install it, not after.
What drives the price up: gate weight (solid steel is heavier than aluminum and takes more labor to shift safely), post damage that requires concrete work, and slide gates with worn rollers that need replacement before the gate can sit level. What keeps the price down: catching the problem early, before the motor has been fighting a binding gate for months.
Estimates are free. Call (817) 840-7067 and we’ll schedule a visit. You’ll get a written price before any work starts.
Why Fort Worth Homeowners Call Carver Gate Repair
This is a trade where no-shows and moving prices have become the norm. We built our process around ending that. Lonnie Burke runs this location, and every job goes out under the same rules, every time.
- Written price before work starts. The number you approve is the number you pay. No “while we’re here” add-ons that show up on the final invoice without your sign-off.
- 365-Day Done Right Promise. Every realignment comes with a written guarantee, good for a full year. If the gate slips out of alignment again inside that window, the second visit is free. No charge, no argument.
- Background-checked, uniformed technicians. The person who shows up is who we said we were sending. You’ll know their name before they arrive.
- Live phone coverage, 24/7. A real person answers at (817) 840-7067, including weekends and holidays. No voicemail tree, no call-back queue.
- Operator knowledge that matters. We train on the motors we service, and the same technician who realigns the gate understands how the operator’s limit switches and force settings work. You don’t get a gate tech and a motor tech. You get one person who knows both.
FAQs – Gate Realignment
How much does gate realignment cost in Fort Worth?
Gate realignment in Fort Worth typically runs $150 to $425 for most residential gates, depending on whether it’s a single swing, double swing, or slide gate. Post resets in concrete add $75 to $150 per post. Call (817) 840-7067 or search Gate Repair Near Me in Fort Worth, TX for a free estimate with a written price before any work starts.
Can you realign a gate the same day?
Yes, in most cases we can realign a gate the same day. Simple hinge adjustments and operator re-sets are done in a single visit. If a post needs to be reset in concrete, that requires a return visit after the concrete cures, usually 24 to 48 hours.
Is it cheaper to realign a gate or replace it?
Realignment is almost always cheaper. A full gate replacement in Fort Worth typically starts around $1,200 to $2,500 depending on material and size, while realignment is $150 to $425. See our broader How Much Does Gate Repair Cost? (2026 Price Guide) - Fort Worth, TX for more pricing details. If the post itself is rotted or the frame is cracked, replacement may be the right call, but most misalignment problems are repairable without swapping the gate.
Will realignment fix a gate that reverses on its own?
Often yes. A gate that reverses mid-cycle is usually binding against its stops or rails, which trips the operator’s obstruction detection. Once the gate is realigned so it moves freely, the operator stops sensing false obstructions and the reversal stops. If the problem persists after realignment, the issue is in the operator’s force settings or the control board. Call (817) 840-7067 and we’ll diagnose it on site.
Do you work on all gate motor brands?
Our technicians work on nine major gate motor brands, including Ghost Controls, DoorKing, Elite, and Mighty Mule. The operator matters during realignment because limit switches and force settings need to be re-calibrated to match the gate’s new geometry.
If your gate is dragging, leaning, or refusing to latch, don’t wait until the motor burns out or the hinge fails completely. Call Carver Gate Repair Fort Worth at (817) 840-7067 for a free estimate. A background-checked, uniformed technician will come out, measure what moved, and hand you a written price before any work starts. The realignment is covered by a written one-year guarantee, and if it slips again inside that window, the second visit is on us.
Serving all of Fort Worth, including Arlington Heights, Ridglea Hills, Wedgwood, Ryan Place, Mistletoe Heights, and surrounding areas. See our Gate Repair in Fort Worth page for the full scope of services, or return to the home page.
Written by Lonnie Burke, Owner at Carver Gate Repair Fort Worth, serving Fort Worth.