Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Installation Across Fort Worth
A new driveway gate in Fort Worth typically runs $2,800 to $7,500 installed, depending on the gate material, opener type, and whether we’re replacing an existing post footing or setting fresh concrete. Most installations take one full day on site, with the concrete curing before the operator gets final programming. Call (817) 840-7067 and we’ll give you a written price before any work begins.
We work across Fort Worth every week, from the wide lots in Ridglea Hills to the newer builds along Chisholm Trail Parkway and down through Crowley Road and McCart Avenue. The soil here moves. Clay expands when it rains and contracts during dry spells, and the freeze-thaw swings between December and March push shallow footings around. A gate that hung square in October can drag by February. That’s why our Gate Installation crew resets posts to the right depth, not just the minimum that holds up for a season. We quote Fort Worth work based on what the ground actually does here, and we build accordingly.
Every job starts with a written price. You’ll know the total before we dig, weld, or run conduit. The crew that shows up is background-checked and uniformed, and the same team handles the whole install. No subs, no hand-offs.
Why Carver Gate Repair Fort Worth Is Fort Worth’s Preferred Gate Installation Company
The Garrison Standard has been our operating rule since 2008. That means a written price before work starts, background-checked technicians on every job, and a 365-Day Done Right Promise in writing on the finished install. If something isn’t right inside that year, we return and make it right. No charge. You don’t chase us; we pick up the phone, 24 hours a day, and answer.
Fort Worth homeowners call us for a specific reason: we treat gate work as its own trade. A general contractor who also does siding, roofing, and fence work won’t know that a Viking operator’s limit switch calibration differs from a Ghost Controls board, or why a 1990s DoorKing opener in Ridglea Hills lacks the entrapment protection UL 325 now requires. Our technicians train on nine brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. When you call about a gate, you’re talking to someone whose entire day is gates.
The 365-Day Done Right Promise isn’t fine print. It’s a written guarantee on every install, good for a full year from the date the job is complete. It covers the workmanship and the components we installed. If a repair or adjustment falls inside that window, the second visit is free.
Lonnie Burke leads the Carver Gate Repair Fort Worth team. The standard doesn’t drift because he doesn’t let it. A live person answers the phone around the clock, including weekends and holidays. You call, you talk, you get a straight answer.
Styles & brands we work with
Driveway Gate Installation in Fort Worth
Driveway Gate Installation on a Fort Worth property means setting steel or wood posts in concrete, hanging the gate leaf, mounting the opener, running the power and safety loops, and programming the travel limits so the gate closes every time without slamming. A single swing gate with a new operator starts around $2,800. A double swing gate in wrought iron, with a new opener and loop detectors, runs $4,500 to $7,500. Sliding driveway gates sit at the upper end because the track, rack, and motor assembly add real labor.
In neighborhoods like Ridglea Hills, where original 1960s and 1970s gate posts have spent fifty years in expansive clay, we often find the footing has shifted or the post base is rusting. We reset posts deeper than the old minimum, below the freeze line, and we size the concrete around the post rather than treating the job like hanging a gate on a fence post.
UL 325 and Entrapment Protection
Any new gate operator in a residential setting must meet current UL 325 entrapment standards. That means photocells or contact edges in addition to the motor’s built-in reversing feature. Older Fort Worth installs rarely have these. If you’re keeping an original operator, we’ll bluntly tell you when it can’t be made code-compliant and why replacement is the honest answer.
Gate Material and Hardware Selection
For driveway gates, we see three real options in Fort Worth. Light steel gates are the most common; they’re strong but need periodic rust treatment, especially with summer humidity. Aluminum weighs less and resists corrosion, which helps near creeks and low-lying areas. Wood gates match ranch-style homes but move with moisture and need sturdier frame construction. The hardware choice matters as much as the gate itself: hinges rated for the leaf weight, a latch that doesn’t bind, and an opener sized for the gate’s actual swing load.
Sliding Gate Installation in Fort Worth
Sliding Gate Installation in Fort Worth typically runs $3,800 to $8,500, with the cost driven by track length, gate weight, and whether the existing footing is sound. A cantilever slide gate costs more than a rack-and-pinion on wheels but doesn’t drag in the dirt, which matters here. Slide gates are the right call for wide driveways where swing gates would eat too much yard space or where the driveway slopes upward and a swing leaf would bind.
We install more sliding gates in the newer subdivisions along Chisholm Trail Parkway than anywhere else in Fort Worth. Those homes have wide side entries and owners want an automatic gate without sacrificing parking room. The failure mode we see most often: the track heaves after a winter freeze, the gate binds, and the motor strains until a gear strips. We set slide gate footings with that specific reality in mind.
Rack and Pinion Slide Operators
A rack and pinion operator mounts the motor on a post beside the gate and drives a gear along a toothed rail welded to the gate’s back side. It’s durable and straightforward to service. The weakness is the track below, not the motor above. If the concrete track has heaved or cracked, we cut it out and repour before hanging the gate. Skipping that step guarantees a callback.
Cantilever Slide Gates
A cantilever gate rides on rollers set back from the opening, with the gate suspended above the ground rather than running on a track. It costs more because the frame must be built rigid enough to carry its own weight without sagging. In Fort Worth, where freeze-thaw cycles shift soil by inches some winters, cantilever gates avoid the binding problem entirely. If you’re replacing a gate that’s frozen up more than once, we’ll often recommend this design even at the higher price.
Trusted Brands We Service in Fort Worth
We stock parts and boards for the gate-motor brands Fort Worth homes actually have installed: Ghost Controls, DoorKing, Elite, and Mighty Mule among them. A DoorKing slide operator from the early 2000s needs a different control board than a newer Elite unit, and we keep the common replacements on our trucks when we run Fort Worth calls. That matters when your gate is stuck open at 7 a.m. and you need it closed before you leave. We don’t wait on a distributor because we planned for what these neighborhoods have bolted to their gates.
Common Gate Installation Problems We See in Fort Worth Homes
- Post footings heaved by freeze-thaw cycles. Fort Worth winters swing below 32°F at night and back into the 50s and 60s by afternoon. Moist clay soil expands when it freezes and settles when it thaws, pushing shallow post footings around. A gate that hung level in October binds by February. We reset posts below the freeze line and use concrete sized to resist the movement.
- Original 1990s operators without entrapment protection. Many Ridglea Hills homes still run their original LiftMaster, FAAC, or DoorKing operators. Control boards from that era burn out in August heat and lack the photocells and reversing features UL 325 now mandates. The board failure is the symptom; the missing safety equipment is the bigger problem.
- Wrought-iron gates sagging at the hinge post in Fairmount. Those 100-year-old posts rust at the base, below the soil line where you can’t see it. The gate drops, drags on the ground, and strips the operator’s gear. The fix isn’t a new gate; it’s cutting the rusted post base, setting a stub post in fresh concrete, and re-hanging the original iron.
- Track binding on new slide gates after freezes. In subdivisions along Chisholm Trail Parkway, rack and pinion slide gates on concrete tracks shift when the ground freezes. Homeowners override the opener, force the gate manually, and bend the rack. We see it every winter. A deeper footing and a true cantilever design prevent most of these callbacks.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Installation in Fort Worth, TX
Expect a basic single swing driveway gate with a new operator to run $2,800 to $3,800 in Fort Worth. Double swing gates land between $4,500 and $7,500 depending on ironwork and opener brand. Sliding gates run $3,800 to $8,500, with cantilever designs at the top of that range. Pedestrian gates, which we also install, start around $900 and go up with material and hardware.
What moves the price: gate material, opener brand, whether we’re replacing posts or setting new footings, and the electrical run from your panel to the gate. We don’t quote a low number and add to it once the job is open. The price is written down before we start, and it doesn’t change unless you change the scope. Call (817) 840-7067 for a free estimate. We’ll measure, walk the site, and leave you with a number in writing.
We Also Serve Cities Near Fort Worth
Our crews cover Fort Worth and the surrounding Tarrant County cities, including Fort Worth proper, Haltom City, Bedford, Crowley, and Southlake. If you’re just outside the city line, call and ask. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, and we run gates in these cities every day.
Serving Fort Worth, TX - Our Local Coverage Area
We’re based in the Fort Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Fort Worth
In most Fort Worth cases, no. A 1970s-era operator lacks the entrapment protection that UL 325 now requires for new installations, and the control boards and gear assemblies are long out of production. If the operator still works and you’re only replacing the gate leaf, we can sometimes rehang the new gate on the existing motor, but we won’t install it without adding the required photocells or contact edges. Call (817) 840-7067 and we’ll tell you straight whether your old operator is worth keeping.
Repair is usually the right answer and costs far less than a new gate in the Fairmount historic district. The sag comes from the hinge post rusting at the base, not from the iron itself failing. We cut the rusted section, set a stub post in fresh concrete, and re-hang the original gate at the correct height. Welding repairs are done to match the antique look, which the historic guidelines require. A new gate is only necessary when the iron itself is cracked beyond sound repair.
The concrete track underneath your slide gate is heaving when the clay soil freezes and thaws. Fort Worth’s winter pattern of 20-degree nights followed by 60-degree afternoons moves shallow concrete by fractions of an inch, just enough to bind the gate and overload the motor. The permanent fix is to remove the old track, pour a deeper footing with proper reinforcement, and reset the track level. Some homeowners upgrade to a cantilever slide gate that suspends above the ground entirely. Either way, call (817) 840-7067 and we’ll assess the track before the next freeze.
Yes. Fairmount is a designated historic district, and any visible gate change to a home within its boundaries requires review under the city’s historic preservation guidelines. Original wrought iron must be preserved where feasible, and new gates must match the character of the home. We’ve worked with these requirements before. We document the existing conditions, quote the work that complies, and handle the paperwork with the city. Don’t order a prefab gate without checking first.
You can, and it works well on single swing and pedestrian gates where running power to the gate would mean trenching across a long driveway or cutting through existing landscaping. Solar kits from Ghost Controls and Mighty Mule are common on Fort Worth installations. The panel needs unobstructed south-facing sun, and the battery must be sized for cloudy stretches. We can tell you honestly whether your site gets enough light to make it dependable. Call (817) 840-7067 and we’ll walk the site with you.
Call Carver Gate Repair Fort Worth for a Written Quote
Call (817) 840-7067 and tell us what’s at your driveway. We’ll schedule a measurement, give you a written price before any work starts, and send a background-checked, uniformed technician to install it. The work carries a 365-Day Done Right Promise in writing. If it’s not done right, we make it right, and the second visit is free inside the guarantee window. That’s the Garrison Standard, and it’s been the rule since 2008.
Written by Lonnie Burke, Owner at Carver Gate Repair Fort Worth.